In this post, I talk about how to get fast fast using data. Anybody can get reasonably fast with a little time and effort. For most drivers, this a year or two. However, as with any craft, the last 10% is what separates the really good drivers from the so-so drivers. Using data will help you break into the remaining 10% much faster than relaying on seat time alone.
Key Performance Indicators (KPIs)
There are lots of books available on the topic of driving faster. If you’re an experienced driver you probably have your favorites and a lot of what you’ve learned should be instinct by now. If you’re just getting started, I highly recommend you first read some books or take a class, because this post assumes an experienced driver. My favorite book is Drive to Win by Caroll Smith.
When working on going faster I keep several KPIs at the forefront of my mind while driving and as part of measuring performance using data. They are:
- How soon am I getting on power relative to apex? Sooner is better, and if after apex then that’s really bad.
- After getting on power, am I staying in it or correcting? If correcting (with throttle or steering), then probably because I got on power too soon or my line was bad, or both.
- What is my top speed just prior to braking for the next turn? Faster is better, and it’s reflective of how well I exited the previous turn.
- How is my braking affecting corner entry speed? You want to maximize corner entry speed and carry it throughout the turn.
- How are my steering inputs into and throughout the turn? Ideally one input and then hold, with little or no corrections.
- Am I taking full advantage of the track surface? Even a couple inches off line can cost precious tenths — something about which a data acquisition system makes you hyper-aware.
- Am I being smooth? Smooth is fast. Ideally, I look like I’m bored out of my mind and about to fall asleep at the wheel, as observed.
It’s far from being a comprehensive list, but it’s manageable and relevant to where I am in my driving development. Your list can be different, but have a list of KPIs for evaluating yourself on and off the track.
Notice that I didn’t include lap time. This, of course, is the ultimate goal but it’s what happens between start and finish that lowers lap time so focusing on it as a means of improving performance is not the answer.
It’s what happens between start and finish that lowers lap time so focusing on it as a means of improving performance is not the answer.
When I first started driving in 2000, data acquisition systems were prohibitively expensive for most drivers — including me. We had crude ‘tools’ at our disposal like a visual speed or RPM check at some arbitrary reference following turn exit. While much better than a seat-of-the-pants approach, it doesn’t compare to the even the lowest cost data acquisition systems readily available in market today.
A very good low-cost option that I’ve used and recommend is the CMS Lap Timer — it’s all that’s needed for all but the most advanced drivers, this is all that’s needed. Don’t let waiting to buy and install an expensive solution keep you from gathering data. (Yes, I’ve talked to people who use this as an excuse.)
A low-cost system like the CMS Lap Timer is all that’s needed to get started collecting data today.
I currently use a Racelogic Video VBOX Lite system to measure performance. Details on why I use VBOX and how it compares to CMS Lap Timer are discussed at the end of this post.
The following video was recorded using my VBOX at the Ridge Motorsports Park in Shelton, WA. I’m sure you’ll agree the amount of information available to the viewer far surpasses what would otherwise be available using a GoPro. You may notice the speed indicator sticking in areas. It’s annoying but it doesn’t affect the log data and I’ve since resolved the issue.
VBOX From the video overlay alone, you can see that I’m able to measure and record the following data relevant to analyzing driver performance:
- Speed (slight issue with sticking in this video)
- Brake pressure (%)
- Throttle position (%)
- Lateral, longitudinal, and total g-force
- Lap times
Be sure to note track conditions, tire data, and any equipment changes when logging data. Here, I’m running Pirelli Trofeo R comp tires at 29.5 PSI (hot, all 4 corners) with 8 heat cycles. Track is dry and in good condition, weather is sunny and 78F.
I should be wearing a driving suit at these speeds, so please don’t follow my example if you’re pushing your car at or near the limits on the racetrack. Wear a driving suit. I’m addressing the situation for myself.
I use three different approaches to analyzing the data:
The approach used depends on time available and what I’m hoping to learn.
Several key factors involved in going fast cannot be easily quantified:
- How smooth am I?
- Am I hitting my apexes?
- Am I taking full advantage of the track surface?
- Am I needing to correct a lot?
- Am I relaxed and not rushing my inputs?
- Am I being smooth and progressive with my throttle input?
- Am I backing off throttle in places that doesn’t seem right, and why?
These can, however, be evaluated qualitatively using recorded video. In reviewing the previous video, there’s lots of room for improvement based on these factors alone. Do the same of your own driving, be self-critical, and apply what you learn in subsequent sessions. Over time, you’ll see your driving improve and lap times go down.
Using this method I’ve become much better at self-accessing my own driving in real-time. At first, my perception of how well driving in real-time was very different compared to as viewed later on video. This is why musicians record themselves while practicing their craft. We sound much better in our own minds when practicing as compared to reality because the human brain filters out mistakes. Playing back the recorded session makes mistakes readily apparent and correspondingly raises awareness, which in-turn contributes to becoming a better player.
One of the benefits of qualitative analysis is that it can be performed quickly and easily between driving sessions, with no special tools or software required. In doing so, you’ll become faster faster because you don’t need to wait until the next track day to apply what you learned. Instead, for a typical track day has 6 sessions, you’ll get 6 opportunities to review and apply what you learned while details are fresh in your head.
The key to lower lap times is in maximizing cornering performance. While the novice driver is inclined to believe its about how fast driven through a turn, the experienced driver knows it all about corner exit speed — especially if exiting onto a long straight. As with all rules there are exceptions. For example, you might sacrifice corner exit speed in a turn if it sets you up for a better turn exiting to a long straight.
Take a quantitative approach to maximize cornering performance by evaluating the following:
- What is my corner entry speed?
- Am I using all available grip in turns? (For mid-turn, steady-state I look at total g-force.)
- How soon am I getting on throttle relative to apex?
- What is my top speed at the end of a straight? (Reflective of corner exit speed.)
Apply the scientific method as a means of improving performance by establishing consistency and then controlling one variable at a time.
By consistent, I don’t mean 80 mph, then 77 mph, then 82 mph, if evaluating — for example — corner entry speed. That’s not even remotely consistent. The variance needs to small else you have no way of knowing the input change you’re experimenting with in responsible for the change.
Considering all the human, mechanical, and environmental factors involved, I’m still amazed how consistent we drivers can get in terms of laying down lap times over 2-3 miles of pavement. Tenths of seconds are normal. While consistency is important, I don’t drive around the track telling myself to be consistent. Instead, focus is on nailing turn in, hitting and pushing my brake zones, smooth corner entry, etc. There’s a lot of feel involved too. So, again, when you think about it that way, it’s amazing how consistent we can be.
The following videos shows two side-by-side laps driven in a reasonably consistent fashion. Please turn down the volume because it’s annoyingly loud.
Once consistent, start experimenting with different inputs one at a time, and observe how performance is affected. You might be surprised by what you discover. For example, a lot of drivers think braking late and hard is the key to fast laps. In a racing situation it can make sense if needed to protect position, but corner entry speed is more important for clocking a fast lap — assuming braking is reasonably aggressive and not coasting, or worse, accelerating into turn entry as a result of braking too early. It does no good to go barreling into a corner hot if it means spending the rest of the turn collecting the car.
Besides braking, some of the other inputs you can experiment with are:
- Turn-in point
- Line through the turn
- Throttle application in the turn
Regarding throttle application, I typically like maintenance throttle from turn-in all the way until time to start powering out of the turn, and then the sooner the better — ideally, prior to apex bearing in mind I drive a car with an engine where it belongs (behind the rear axle). The only exception is if I’m trying to assist rotating the car through a tight turn.
Using this method you’ll watch your personal bests become your new norms over time as part of process that continues to repeat itself. Since it’s normal for a road course to have anywhere between 10 and 16 turns, go after the turns leading onto the big straights first since this is where you’ll see the biggest return on investment. As you gain more experience with a particular track, turn your focus next to the turns leading to medium-length straights, and finally the remaining turns which have diminishing returns.
Before moving on to the next section take a look at the following track map of The Ridge Motorsports Park. Write down on a piece of paper the turns that you’d prioritize working on after you’ve acquainted yourself with the track and are ready to start finding speed. If you have experience with this track then then you should have an opinion here. I’d love to hear from think you have a better approach — write me so we can compare notes. I’m always looking for more speed.
VBOX includes a software application called Circuit Tools that runs on the PC and Mac. Among other things, it enables you to analyze your driving using graph data time synchronized to video. Once in Circuit Tools, you’ll have access to much more information than is available from looking at the video alone. It also enables you to view data over the length of the track with user specified channel data for visualizing patterns and identifying complex relationships, such as the impact of cornering performance on overall lap-time and braking on corner entry speed.
The most powerful feature of Circuit Tools is being able to compare two or more laps side-by-side. Laps compared can be from the same lapping session, across multiple sessions for the day, or even from different days. You can also see how you compare to another driver if you’re OK having he or she drive your car — just be prepared to check your ego at the door because you can’t blame equipment or tires if it turns out you’re slower.
The following screenshot shows a delta-t plot comparing two laps from a 30-minute lapping session at The Ridge Motorsports Park. Lap 7 (red) is the fast lap and it serves as the basis for comparison, as shown by the horizontal red line. Lap 10 (blue) is 1.26 seconds lower and we’re about to find out why using delta-t and various other channel inputs as we work our way around the track. The red dot on the track map encoded onto video shows track position. Adding brake channel data is a good way to mentally rough in the turn locations without having to scrub through the timeline when evaluating the delta-t plot.
Using delta-t, it’s easy to spot where the additional time is being accumulated in Lap 10. For the purposes of this post, I Photoshopped in the 5 segments that are readily identifiable as being responsible for most of this time — they’re highlighted in red and labeled A, B, C, D, & E. I’ve also Photoshopped in turn references and calculated the time accumulated for each of the highlighted segments since this is not an interactive demo. The keen eyed will note these segments sum to 1.30 s instead of the 1.27 s. This is not unexpected since we’re not summing across the entire path, and it supports we have a good approximation.
It’s easy to spot that most of the time added (60%) is in segments D and E. This isn’t surprising since T12 and the T14-16 complex lead onto medium and long straights. If trend data shows I’m not able to consistently nail these turns then I will prioritize working on them over other turns because the ROI is much higher. That said, let’s closer look at A, B, & C. They’re a bit more interesting and goal here is to simply demonstrate an approach.
Section A is unique in that there’s no braking involved. In my opinion, T2 through T5 is the most technical part of this track. What happens in T3, T4, and T5 starts with how well entered into T2. This is not something that can be easily accessed using data, but hints of it are evident in the following screenshot.
Here you can see how I turned in sooner in Lap 7 (red), which in turn enabled me to start releasing sooner. Note the steering angle inputs and corresponding increase in speed where I’m a full 5 MPH at instance shown. The slower Lap 7 is due to bad setup (off line, wrong attitude) coming out of T3, which starts in T2, and I needed to correct as a result. In this case, I was able to salvage T5 so I didn’t get penalized in the back straight leading to T6. Conceptually, one should think of the back “straight” as starting at T4 exit.
In general, I seek to brake as late as possible without compromising corner entry speed. If I need to choose between the two, sacrifice braking. This is also where things get real busy and — in my experience — is what separates the professional drivers from doctors and lawyers. (That’s a Carrol Smith reference by the way, and I include myself in that group even though I’m not a doctor or a lawyer.)
I like to rely on LongAcc for how hard braking. BrakePos is not a good indicator because heat and tires can affect how much pedal force is required for a specified braking force. However, BrakePos is good for monitoring pedal inputs, including how early or late to brakes.
I like to rely on LongAcc for how hard braking. BrakePos is not a good indicator because heat and tires can affect how much pedal force is required for a specified braking force.
The following two screenshots show activity in the breaking zone leading up to T6 and T6 entry, respectively. Let’s start with the braking zone.
Braking in the slower lap (blue) is earlier and more abrupt as can be seen from the BrakePos and LongAcc channel plots. The early brake causes start scrubbing speed sooner and delta-t starts to grow. The abruptness unsettles the car as evident in the LongAcc plot line and combined G (table to left). The impact manifests itself trail braking into T6, where entry speed is about 2.5 MPH slower.
Segment C[Coming soon]
Predictive lap timer
A predictive lap timer is a great way to see in real-time the impact a change or mistake has on your lap-time. Suppose you’re half-way around the track and your knocking on the door of a new personal best according to your timer (e.g., -0.07). Now you’re just one mistake away from blowing it. Focus!
It wasn’t until I started running a timer regularly that I truly appreciated just how much using every inch of track surface matters. Being 6″ off line didn’t seem so bad until I started seeing the results in real-time on my timer — it was a rude wake-up call. This also holds for the impact of otherwise seemingly small mistakes. Putting down fast laps requires focused execution and no mistakes. The predictive lap timer has been indispensable in training me to think this way — as opposed to try driving faster, which is a surefire way to go slower.
I don’t change equipment very often because it interferes with my ability to access how I’m improving as a driver. It’s also expensive.
I don’t change equipment very often because it interferes with my ability to access how I’m improving as a driver.
I’ve seen and talked to a lot of people who spends thousands on go-fast parts only to discover their lap times are virtually unchanged. The disappointment is evident in their expressions. I know the look and feeling because I’ve been there. When racing, I tried out 4 different differentials at great expense, blood, and sweat. I was convinced each ratio would be the magic bullet but my lap times didn’t change one iota. Very frustrating and, again, disappointing.
I’m not going to be that annoying guy that goes on and on about how you shouldn’t upgrade. Some upgrades are necessary for even the beginning driver. Safety equipment, brakes, and a good set of pedals come to mind. If there’s something about your car that’s interfering with your driving, fix it! For example, lots of cars have soft transmission and engine mounts that cause the components they’re designed to support to shift under load. This can lead to the infamous “money shift” where you drop into 2nd instead of 4th, and pop goes the motor. Yep, I’ve been there too.
Let me just offer that if you’re not driving your car near or at its limit then making it faster isn’t going make you go faster, and it certainly won’t make you faster.
If you’re not driving your car near or at its limit then making it faster isn’t going make you go faster, and it certainly won’t make you faster.
If and when you do make upgrades, change only one component at a time so that you can correctly assess the cause-effect relationship of the change on lap time. This hold true for setting changes well, such a tire pressures, camber, spring rates, sways, and damping.
Always have a plan for the day
I like to have fun at the track, but you’ll never hear me say “I just want to have fun.” I always set aside sessions to have fun with drivers I trust on the track. Taking cool video footage, hanging it out in a particular turn just for the fun of it, doing some lead-follow, etc.
I also always dedicate at least 3 or 4 sessions to working on getting faster. In a nutshell, I recommend actually doiong what we all get taught in driving school, which is to have a plan for the day on what to improve. It can’t be get new personal best lap time — that’s not actionable. Instead, focus on 1 or 2 turns (or some other aspect of your driving) based on what your data it telling you. If you’ve analyzed it correctly then your lap times will drop as a consequence of your improvements in these areas.
Track day strategy
It’s pretty funny actually. All track days start and end pretty much the same way. In the morning, when it’s often cold and dewy, everybody’s in a hurry to get out on the track and go fast. There’s almost always an incident and traffic is so heavy, people are complaining about how others aren’t pointing-by. If you’re a regular, you know what I’m talking about.
I generally don’t waste my time going out for the first session. If I do, it’s just for a very mild warm-up or to do an equipment check — and even then, I’ll go out mid-session. The first couple laps are usually under yellow so the entire group only goes as fast as the slowest car, which can be agonizingly slow.
On the flip side, it’s very common to find the track virtually empty at the end of the day. Refer back to the videos above where I appear to have the track to myself. All those people who couldn’t wait to get on track in the morning only to drive in a traffic jam are nowhere to be seen.
It’s very common to find the track virtually empty at the end of the day, and this is the ideal time to work on improving driving skills.
There are lots of reasons why people may need to leave early — I’m not faulting or ridiculing them. Family commitments, equipment problems, tired, wreck, etc, are all very good reasons. However, to the extent possible, use this to your advantage as you plan out your day.
I always use the last couple of sessions of the day to focus on improving my driving and finding speed. I’m warmed up, have previous sessions to reflect upon, and — because traffic is light — I stand a chance at clicking off a new personal best.
I also much prefer back-to-back driving events at the same track as compared to two events separated by days or weeks. It’s a challenge to fully analyze session data during the day without a support crew. In between session is spent checking tire pressures, torquing wheels, refueling (which can mean a trip to the gas station), dealing with equipment issues, and socializing. Time disappears. When driving back-to-back days I use the evening of the first day to delve deep into my data and apply what I learned the next day, while thing are still fresh in my head.
When driving back-to-back days I use the evening of the first day to delve deep into my data and apply what I learned the next day, while thing are still fresh in my head.
Unfortunately, there’s a trend by some track organizers to run back-t0-back days clockwise one the first day and counter-clockwise the next. This effectively makes for two completely different tracks, but lots of people like this format because it’s fun. I don’t attend such events.
VBOX and CMS Lap Timer
I’ve used VBOX and CMS Lap Timer and they’re both great systems for their respective price points. In this section, I’ll briefly touch on the relative pros and cons. I also include video footage taken by each for the same time to help you see how they compare.
As mentioned ,VBOX is a more expensive and capable system. You can forget about impressing your friends with cool in-car video footage but it gets the job done in terms of providing visual references while analyzing your driving, which — in fairness to VBOX — is the point of this system. For more information and installation instructions, see this post.
Some key points to consider:
- VBOX support multiple video inputs (2 for VBOX Lite, more for higher-end units).
- System utilizes bullet cameras that can be positioned as desired.
- SD video quality means not needing to worry about running out of storage.
- External microphone input
- Can be integrated and wired directly into the car so you never miss footage.
- Moderately expensive
- SD video quality
- Logging data is rendered directly onto video output.
The last bullet requires a bit of explanation. By rendering log data directly onto video output you cannot get the original video footage back. Practically speaking this isn’t an issue since the video quality is so poor you’re probably not going to want it for any thing other than driver analysis.
CMS Lap Timer
The basic CMS Lap Timer requires only an iPhone or Android device, a windshield mount ($10-$20), and the app (free version and pro version from $20). A high resolution GPS receiver is also recommended for better accuracy and costs around $100. Assuming you’re already an iPhone or Android user, this means you can analyzing your driving with less than $200 invested. A bargain! If you don’t have an iPhone or Android phone, an iPod Touch also works (no phone contract required). Still a very inexpensive solution. Details can be found here.
With the basic setup, you get the essential information needed to analyze your driving:
- Video with track position indicator for reference
- Analysis software
- Ability to share and compare session data
Depending on your vehicle, you may also be able to purchase an optional ODBII interface that can capture and log additional parameters such as RPM, throttle position, steering input angle, and more. I have just the basic setup.
- Very inexpensive (if you have an iPhone or Android phone)
- HD video quality
- Video is stored separately from logged data so original captured video is retained.
- SD video quality means not needing to worry about running out of storage.
- No ability to customize how data is displayed
- Depending on device and usage, amount of available storage could be a concern
- Limited to single video input (the phone camera)
I didn’t start sport driving and road racing until my 30s and if I could go back in time I’d almost certainly start sooner. It’s an exciting lifestyle that challenges you on many levels and connects you with great people. I started driving cars since before I had a license. My first experience driving a car was grandma handing me the keys to her 1974 Z28 Camaro at age 13. It came naturally because it was just like driving a motorcycle but easier. I drove it like I stole it. By age 15, I was sneaking out the family cars late at night to go drag racing, then rebuilding engines and gearboxes with my brother so mom could get us to school and her to work. After getting my driver’s license life at age 16, everything revolved around cars, drag racing, and cruising the strip. Life was like a scene out of American Graffiti. That all abruptly ended when it came time for college.
Even though cars exited my picture, a good college friend of mine was into road racing. He had a ’65 fastback Mustang that was track prepared. I wasn’t impressed by it because it wasn’t very powerful and it was a bit rough looking. Perhaps he sensed this because one day while driving he looked over to me and said hang on. We were speeding down the road and there was a sweeping right-hand turn ahead. He accelerated towards it and at one point a I screamed ‘slow down!’ while bracing for impact. Still keeping into the throttle, he finally braked hard, turned in, and then back on throttle to accelerate out of the turn. The car stuck to the road! I couldn’t believe it. It seemed as though we had just cheated physics. That was my introduction to what road racing is like. It made an indelible impression and left me with a latent interest in getting involved, but it would have to wait until some future time.
I got my first taste of what road racing is all about in a car very similar to this. A friend drove it hard into a big right-hand sweeper and I was sure we were going to die. The car stuck and I my fear turned into laughter because it seemed as though we cheated physics. Suddenly, handling (chassis design and suspension tuning) became a lot more interesting than 0-60 and 1/4 mile times, trap speeds, and horsepower.
It’s random luck that finally got me involved in driving because my girlfriend (now wife) gave me a gift certificate to a high performance driving class at ProFormance Racing School. This was my introduction to sport driving and I loved it. It’s no wonder I married that girl! It was much easier and more accessible that I had imagined to drive fast on a racetrack. I had looked into the costs associated with some of the big names schools throughout the country but was turned off by their costs and distance — I wasn’t interested in a one time experience. However, Pacific Raceways (called Seattle International Raceway at the time) was just a 35 min drive from work and ProFormance held regular lapping days, including afternoon programs at an affordable price. These were great because I could go to work in the morning, get some afternoon lapping in, and then back to finish my work for the day.
It was only about a year before I had my sights set on racing. Lapping introduced me to racers who came out to the track from time-to-time to work on their skills or test their cars. The more I learned about racing the more I wanted to get involved because I’m a competitive person and competition is something that hot-lapping lacks. I took the plunge and my life changed. Outside of work, everything revolved around racing and if I had my way there’d just be racing. I raced for 5 years before deciding to take a break in the middle of the race season. We took a trip to Europe and I then decided to take the rest of the season off. Unbeknownst to me I had ‘taken the [racing] needle out of my arm’ and I was enjoying the extra time I had to do other things in life. 1 year turned into 2, then 2 into 3. Eventually I sold my racecar.
Recently, I got back into driving casually and I intend to keep it that way. I love the people and energy at the paddock, but of course, most of all I love driving. Since returning I’ve had many fuel pump conversations with people wanting to learn more about my car and racing. Often times teenagers just like me when I was their age. I tell them whatever they want to know, but always send them off with some friendly advice to go to the track to learn more and get involved. Had somebody given me similar advice I would have likely gotten involved sooner. It’s with this in mind that I’m writing this short introduction to the sport and how to get started.
Road Racing and Sport Driving
Road racing does not mean racing on the roads. That’s illegal and you can lose your license and even go to jail. Road racing takes place on purpose-built race tracks (also called raceways or road courses). Unlike oval tracks which are used for NASCAR and Indy racing, road courses have several turns designed to challenge the driver, and vary in their length and number of turns. There’s a vast range of cars that participate in road racing. At one end of the spectrum is the modern Formula 1 car, which is more inverted airplane on 4 wheels than automobile. At the other end of the spectrum are older closed wheel cars like a Volkswagen Rabbit, which is less performant than today’s average family sedan. People will race just about anything and budget usually dictates choice. Wouldn’t we all love to race Formula 1 cars?
The following photoset shows some typical road courses and the various levels of the sport.
Roadmap to Racing
My progression into racing was typical and as follows:
1. Attend an introductory high-performance driving class. Associated with each racetrack is a usually a school. I attended the Proformance Racing School Introduction to HP Sport Driving class where l learned about things like ‘the line’, weight transfer, understeer and oversteer, and the importance of being smooth. Exercises helped drive home the concepts followed by some actual on track driving. Even if you don’t continue on from here the lessons learned are beyond the average driver education curriculum and will make you a better driver on the street. Ironically, public roads are a much more dangerous place to drive than the racetrack. On racetracks, there’s no opposing traffic, pedestrians, trucks with unsecured loads, sudden slowdowns from congestion, kids running into the road, and you don’t have to deal with drivers who are drunk, distracted, or otherwise impaired. Not a day goes by that I don’t apply some of the principles I learned in my high-performance driving class to my everyday driving.
“Not a day goes by that I don’t apply some of the principles I learned in my high-performance driving class to my everyday driving.”
2. Develop skills at hot-lapping days, also known as driver education (DE) events. Getting fast requires practice or ‘seat time’ as drivers like to call it. It’s no different than anything else we humans need to go through in order to get good at something whether it be playing an instrument, golf, or downhill skiing. What you get out of your day depends on what you put into it. You can make it an opportunity to drive fast or practice getting faster. The first if fun, the latter is work. I always take the time to do both. Having an instructor in the car is optional (after being cleared to drive solo) but will help you develop skills faster and prevent bad habits from forming.
3. Successfully complete a competition racing class. I did the 2-day Competition Class at Proformance. You’ll learn about the rules and protocols of racing, what all the flags mean, gridding, what a splitter is, how to pass, etc. You also learn what not to do such as blocking, being ‘helpful’ to faster traffic by going off line, etc. Of course, you’ll also get a chance to experience racing for the first time.
4. Go racing. Sports Car Club of America (SCCA) and National Auto Sport Association ( NASA) are the two most popular sanctioning bodies in the US for road racing. I happen to live in the Pacific North West where International Conference of Sports Car Clubs (ICSCC) is very popular among drivers, so that’s where I raced. One of the nice things about ICSCC is that as a novice racer they don’t dump you right into racing with experienced racers. ICSCC’s program progresses you from Novice -> Area -> Senior driver. Advancement doesn’t require you to be fast, but demonstrated ability follow the rules and not endanger yourself and others.
The following videos is from hot-lapping day with ProFormance racing school at Pacific Raceways. It was common for me to have an instructor out with me for my first year, and this video is from very early on when I first started driving. As a bit of trivia, the Pacific Raceways was called Seattle International Raceway (SIR) back when these were recorded. Also, Turn 8 and 9 merged right onto the drag strip which was very dicey in the rain because the VHT that gives dragsters more traction becomes very slick in the rain.
You don’t need a fast car to get started in sport driving. All that’s required is access to a well maintained vehicle which does not put you and others at risk. I’ve even seen folks show-up in minivans. Personally, I think this is pushing the limits of sensibility but if it means getting out there and learning then it’s arguably a better choice that waiting for the ‘right car’ to come along.
In my opinion, the best cars to start with are low in power, light (under 2800 lbs), and nibble – drivers call them ‘momentum cars’ for reasons that will become clear in a moment. If you can be fast in a momentum car, you’ll be fast in almost anything you drive.
“If you can be fast in a momentum car, you’ll be fast in almost anything you drive.”
With a powerful car, much of its lap time performance comes from being able to accelerate quickly down the straights. If you don’t drive through the turns fast and get good exit speed, the impact to overall lap time is less relative a lower power car (assuming also lower power / weight). In other words, power can easily become a crutch for bad driving and easily woo you into thinking you’re a hot shoe driver because you’re faster that all the other [slower] cars.
A momentum car requires you to drive well in order to turn fast laps by driving through the turns as fast as possible to minimize scrubbing off speed that takes power you don’t have to reclaim easily, and hence the term ‘momentum’ car. Later in your driving career when you transition to a high power car, you’ll drive it like a momentum car but also have the straight-line power to boot. Then you’ll be fast driver in a fast car, instead of just a driver in fast car.
Another advantage of low power cars is that they’re generally less expensive than high-power cars. Not just in purchase price, but more importantly in terms of overall cost. And if you’re going to get serious about driving, you need to consider the overall costs which can easily overshadow purchase price sooner than you might expect depending on how much you drive. High power cars have big tires and brakes which are proportionally more expensive than the smaller tires and brakes found on low power cars, and you’ll be changing tires and brakes a lot if you get serious about driving. Driveline components are more highly stressed and expensive to repair on high power cars, and things will start to break if you track your car a lot so you need to factor in cost of replacing clutch, changing wheel hubs, engine repair (or even replacement) if you get serious about driving. When all costs are consider, the car you think you can afford probably isn’t the car you can actually afford.[box type=”bio”]
When another driver calls you fast it means you’re fast and not the car – it’s the biggest complement a driver can receive. You can be a fast driver in slow car. You can also be a slow driver in a fast car, even though you might be turning faster lap times than the fast driver. The most rewarding experience as a driver is being faster in a slower car. Of course, being fast in a fast car is the best you can do but there’s always somebody faster so be prepared to have your ego bruised. When you’re in a fast car there are no excuses. (Hint: If all else fails, blame it on the tires. That seems to work pretty well.)[/box]
“Driving with your wallet.” It means limiting how much your willing to push yourself for fear of damaging your car. When getting started driving it’s not an issue, but eventually you will reach a point where you need to push beyond your comfort level to improve. If you’re preoccupied with worries of damaging your car then it will affect your push and and ultimately how quickly you progress. Ironically, a slower and less expensive car can actually turn you into a better driver faster than the really expensive and fast one unless you’re made of money. Incidentally, pushing oneself should not be confused with recklessness. Your instructor can teach you techniques for pushing the limits in an incremental fashion so it can be done safely, but it does involve getting out of one’s comfort zone which the the wallet can influence.
When getting started in driving you’re much better off spending money on instruction and extra lapping days than spending it on expensive performance upgrades. Having said that, you’re going to eventually need or want to start upgrading your car if you find yourself lapping frequently.
The biggest upgrade to make your car go faster is in you! With this in mind, prioritize areas that are affecting your driving first. If you find yourself hanging on to the steering wheel in the turns, invest in a better seat. If you’re having problems working the pedals get some driving shoes and adjustable pedal covers, and work on adjusting them until they feel right. If you lack confidence in your brakes because they’re fading or squishy, upgrade your braking system. You’re never going to get better or go fast if you’re concerned about being able to stop your car.
“The biggest upgrade to make your car go faster is in you!”
You’ll also want to consider safety equipment early on. At the risk of sounding cliche, you can never spend too much money on safety equipment. There. I got that out of the way. Having said that, if you’re driving a car capable of going 160mph into Turn 1, you might want to give a lot more consideration to safety equipment that the person driving a car capable of only 110 mph. That extra 50 mph amounts to over twice the kinetic energy of the slower car. A rollbar, fire extinguisher, harness, and Hans device might not be a bad idea before you go adding more power. Seems obvious when put this way, doesn’t it?
When it comes time to make your car go faster, follow the scientific method and change one thing at a time. It will help you get smart about different component changes contribute to a car’s overall performance. It’s you change a bunch of stuff all at once, then you’ve robbed yourself of this opportunity. What’s more, a change can hurt a car’s performance even if a performance part. If you change more than one component at a time, you’ll be hard pressed to single this component out or even know it’s holding you back. (You might be blissfully thinking you improved your car’s performance when in fact you took 2 steps forward and 1 step back.)
The following photoset illustrates the development of my M3 Lightweight. It slowly but surely evolved from a street car to a racecar. I developed it without consideration for race class and rules. This was a mistake in retrospect. In the end, the only class it fit was essentially a ‘free’ meaning pretty much anything is allowed in terms of go-fast modifications. At risk of offending some folks, it’s my opinion unlimited classes like these are essentially a car constructors’ classes based on who can build the fastest car (i.e., spend the most money) as opposed to a drivers’ class. I was interested in the latter. Since the car was developed to the point of no turning back I ultimately sold it.
Transitioning into Racing
Racing requires that you have a competition license. Each sanctioning body has its own rules regarding licensing requirements so it’s a good idea to figure out where you want to race and then refer to their respective regulations and rules. Or, do like I did and find someone already familiar with the regional club racing scene and ask lots of questions. You’ll also need (and want) to attend a competition school. There are nationally known ones like Skip Barber and Bondurant, but there’s a good chance your local school will also offer classes and be more plugged into the local scene where you’ll be racing. For example, I attended ProFormance Racing School’s competition program which is well known by ICSCC, the regional sanctioning body where I raced.
Contrary to what you might think, you don’t actually need to be fast to go racing – that’s only required if you want to win. What’s required is that you’re not a danger to yourself and others. This means being predictable, aware, in control, and an understanding of the rules and protocols of racing. With the exception of the latter, you might already think you’re all of these things and hopefully you are in day-to-day life. But to drivers, these terms take on a different meaning and they take time to develop. If on a hot-lapping day you’ve got a line if cars in your rear-view mirror that appear to be scrubbing your mirrors, that’s actually you driving off line and failing to recognize that you should be pointing them by. and you’re not quite ready to go racing yet.
“Contrary to what you might think, you don’t actually need to be fast to go racing – that’s only required if you want to win.”
Seat time will help you develop the skills you need to go racing and hot-lapping days are the best way to get this. They’re typically organized into two (2) or three (3) run groups based on driver experience level and that alternate throughout the day. This way you don’t have experienced drivers intimidating inexperienced, and inexperienced frustrating experienced. Initially, you’ll be overwhelmed that you’re driving your car really fast on a racetrack while unaware that you’ve actually created a traffic jam of cars waiting for you to point them by. Eventually, you’ll learn to scan your mirrors and spot faster traffic well before it’s on you’re bumper. Once you can do this, you’ve taken your first step towards becoming a racecar driver by demonstrating that you’re comfortable on the track aware of your surroundings. Over time you’ll develop car control skills, be checking turn stations, learn to control emotions, and start to develop a taste for what it’s like to compete. At some point, you’ll be ready and may have the desire to go racing. For me this happened after about 1 year of hot lapping.
Once you’re ready to go racing register for and attend a competition class — it will introduce you to the ‘rules of the road’ in competition driving. Yes, racing does have rules and lots of them. Knowing, following, and even taking advantage of the rules can make the difference between wining and loosing a race. In competition driving, there’s a lot more to wining than being fast. Being fast is something you should have focused on while hot-lapping but now you’ll need to turn your attention to racecraft and strategy, which you’ll be introduced to in class. You’ll also learn how about and practice passing (who owns the line, side-by-side through a turn, etc.), and in general everything else you need to know that you didn’t learn and experience in lapping days.
“Knowing, following, and even taking advantage of the rules can make the difference between wining and loosing a race.”
After graduating from competition class, you’re ready to go racing. Some sanctioning bodies having you jumping right in. I started with a sanctioning body that organizes races in the Pacific Northwest called the International Conference of Sports Car Clubs (ICSCC), or just ‘Conference’ in short. For the most part, it follows the same set of rules and procedures outlined by the Sports Car Club of America (SCCA) organizes races in the area but a far fewer number of them which might explain why ICSCC came into existence. Conference has an onboarding procedure for new racers that involves a progression from Novice -> Area -> Senior driver. This eases new drivers into competition which is better for everybody involved. The following photoset describes each phase an my journey from Novice to Senior driver.
The following video shows a full race from before start to finish. You can see the idle time before the race which I use to mentally prepare myself. Exiting the grid, there’s the splitter and then scrubbing in the tires and getting heat into the brakes on the pace lap. The most exciting moments of any race for me are the start and then the strategy that starts to unfold when first coming upon lapped traffic.
Costs of Racing
“How do you make a small fortune racing? Simple. Start with a large fortune.”
It’s impossible to know how much fun racing can be unless you’ve experienced it firsthand. Anybody calling it a hobby is an outsider and doesn’t get it. It’s highly addictive and it can change your life for the better, or worse if you’re not careful. Racers frequently equate its addictive powers to that of a drug addiction. It’s like inserting a “needle in the arm” the saying goes.
The most important thing I learned in competition school had nothing to do with the competition part of racing. One of the other students was a gentleman in his early 50s and he had a beautifully prepared Mustang racecar. At one point he commented the car cost him his entire retirement savings. I was stunned. I made myself a promise that wouldn’t me one day.
As mentioned, the costs associated with racing go well beyond purchasing and building a car. If you don’t have experience in racing, then chances are the car you think you can afford to race aren’t what you can actually afford. Go back to the beginning. I started lapping with a brand new Porsche 911 Turbo and by the time I was racing it was in a 15 year-old BMW 3-series. Significant factors contributing to costs include the following:
- Acquire or build racecar*
- Tow rig (truck and trailer, plus fuel and maintenance for rig)*
- Annual and biannual maintenance for items such as brake calipers, wheel bearings, clutch, and engine rebuild.*
- Consumables such as tires, brake pads and rotors, fuel, and oil.*
- Upgrades to car to make and keep you competitive.*
- Race entry fees
- Food and lodging fees when traveling to venues far from home
- Driveline repairs when stuff happens (blow engine, gearbox broke, differential broke, etc.)
- Bodywork / chassis repairs when stuff happens.
Items marked with asterisk (*) don’t apply if you’re renting a car, but are replaced with the cost to rent. Except for fuel and oil, nearly all costs associated with the racecar itself will vary significantly depending on the car. A newer Porsche 911 is much, much, much more expensive to race than an older BMW E30 racecar when all of the costs are added up. Consider everything before taking the plunge into buying a racecar. Renting gives you an easy out if you find you picked the wrong class or car.
Life as a Racer
How much your life changes will depend largely on if you’re an owner driver or just driver. In professional racing, driving spend their time practicing, driving, and preparing to exercise their craft in a car that somebody else owns. In club racing, you don’t get paid to race and the majority of drivers are driver-owners meaning they race and own their own car. If you’re financially fortunate, you can pay somebody to build, prepare, fix, maintain, and tow your car to events for you. However, club racing being what it is, this is not the case for most drivers. There is one alternative path to owning which is renting, which is discussed below.
Racing may take place on Sunday, but anybody watching a race is seeing only the tip of the iceberg in terms of the preparation, planning, and time involved. Assuming the car is fully prepared and ready to go racing, a typical Conference race weekend plays out as follows, assuming a local race:
Thursday – Load-up car and equipment into trailer. While at the track, you need more than just your car. Tools, fuel, spare parts, tents, tires (race rubber vs practice / qualifying rubber, and rain tires in case of rain), are just some of the things you’ll need to have on hand in order to get through the weekend. Racers are always helping each other out but you cannot go empty handed. I’d take extra spares just in case somebody else had problems. Sooner or later, people you help out will return the favor. It takes about 6 hours to get everything loaded up and ready to go.
Friday – It’s common for a test-and-tune today to precede the race weekend. The track is open all day long (no run groups) so you can dial in the car. It’s also a great way to get some extra practice time or verify everything is OK and in working order coming of the heels of an upgrade or repair. Before driving, time is spent unloading and setting up your pit for the race weekend. This can take a couple of hours.
Showing up for test-and-tune also lets you secure your space in the paddocks for the weekend. All the other racers will be lined-up late Friday evening awaiting entry or showing up first thing Saturday morning and scrabbling to find a good spot. Getting a nice paddock spot can make your race weekend a lot nicer if you’re close to power, water, friends, and on asphalt as opposed to stuck out in the weeds away from everything and your friends network.
Saturday – Saturday is spent practicing and qualifying. For each race entered, you get a practice session in the morning and then a qualifying session in the afternoon. A lot of racers enter two races (a primary and a secondary), so that results in 2 practice sessions and 2 qualifying sessions. I often entered for 3 races but didn’t participate in all of the practice and qualifying sessions. I just wanted a lot of seat time.
Sunday – Sunday is race day. The day starts with morning qualifying sessions. Qualifying determines your grid position. It puts the fastest cars / driver near the front and slowest at the rear so you don’t have mayhem when the green flag drops. For each race entered, your starting grid position is determined by the best (lowest) qualifying time from Saturday and Sunday. If it’s raining or the track is otherwise slow on Sunday and the track was fast on Saturday, there’s really no need to go out and qualify again. Save your car. It’s not worth something breaking now that you’ve made it this far. Also, except for your primary race, consider if you really need to qualify again. Usually, secondary races are races that your car is not competitive in because they’re higher-spec classes so you’re allowed to race because your car [easily] fits within the rules. Unlike your primary race, you’re just racing for fun and practice, not to win.
The afternoon is spent racing. Each race lasts 30 minutes and there are a lot more race classes than there is time to run a race for each class, so multiple classes are combined into a single race. The organizers try to group classes so there’s not a big spread in performance but sometimes there’s no way around it and you can have very fast cars on the track at the same time as slow cars. If you’re in a slower car, you need to be really heads-up because the fast cars seem to appear out of nowhere and the speed deltas are large. Open wheel cars never mix with closed wheel cars. When you’re racing, you’re racing against the cars in your class. There is no overall race winner. Even if you’re the 4th person to cross the finish line, you’re still the winner if you’re the first of the cars to cross the finish line in your race class.
Your day is far from over after the race has ended. The pit needs to be torn down and trailer loaded back-up, then the trip home. You’ll be exhausted by time you get home so everything stays on the trailer and right to bed.
Monday – If you think you’re going to have a productive day at work on Monday, you’re kidding yourself. You’ll be sleeping in and then there’s still that trailer to think about that’s sitting in the driveway. It’s needs to get unloaded at some point and returned to the storage facility (I kept my trailer at a storage log about 15 minutes from home). Unloading can wait until after work if needed, but it needs to happen at some point during the day. Expect a long lunch talking war stories about the race weekend with race buddies.
Between Races – What happens in between races depends on factors often outside of your control. Most often, your time is spent fixing something that broke or an issue with the car that is affecting its performance (and your ability to win). Even if the car had a good race weekend, time spent inspecting the car and replacing wear items will help it stay that way. Finally, if you’re like me, you’ll be spending whatever remaining time you have tinkering and improving the car in whatever way the rules allow room. A big part of racing is reading, understanding, and taking advantage of the rules wherever you can. Understanding and interpreting the rules is a sport in and of itself. Racers who don’t read and understand them are leaving themselves at competitive disadvantage.
Renting versus Owning
When I started asking around what it cost rent a racecar for the weekend my first instinct was to want to go out an buy a used racecar instead, and that’s ultimately what I did. On the surface, it seems like owning might be a lot cheaper but I invite you to refer back to the costs of racing topic from above. At the club level, driver-owners renting their cars are simply looking to help cover their costs and very few, if any, are making a profit.
Advantages of Renting
- Arrive and drive. The car owner typically handles building, maintaining, fixing, and transporting the car to the race venue, and setting up everything at the paddock. You arrive rested and can focus on your driving. No need for a tow rig, garage, tools, and mechanical know-how.
- You’re not committed to a particular car or class. If the class lacks the level of competition you’re looking for, you can easily switch over to a different class. If you like the class but the car is not competitive, you can find another car to rent.
- Less expensive than owning. When all costs are considered, renting is usually less expensive than owning.
Advantages of Owning
- If the car breaks, you can fix it on your own terms and timeline. You may even decide to throw in the towel for the season if the damage is really bad. If renting, the owners may need to have the car on the track in time for the next race and grease local shop owners with extra money to expedite it through their shops, and you’re responsible for all costs associated with the car breaking while you’re driving. (There can be some gray area here when it comes to mechanical depending on your business arrangement.)
- You can drive the car without regard or concern for the owner or other renters who may be driving that weekend. The first time I rented, the parting words from the owner were go have fun and win, but please remember I’m in the running for championship so please don’t break the car.
- If you’re your own crew as is the case for most driver-owners, there’s an entirely different dimension to racing that renters never get to experience. This includes driving and setting up the car to handle, which can become a competitive advantage once you start to understand the relationship between what the car is doing on the track and how adjustments can improve or worsen a car’s handling.
If you decide to rent, keep in mind that you’re entering into a business relationship between you and the owner. It’s best to agree to terms in writing, which should cover who pays for what, services to be provided at the paddock, what happens in the event of damage to the car (mechanical, racing contact, or off-course impact).
My favorite books about racing are (in no particular order):
- “Going Faster! Mastering the Art of Race Driving” by Carl Lopez
- “Drive to Win” by Carroll Smith
- “Speed Secrets: Professional Race Driving Techniques” by Ross Bentley
Regarding Carroll Smith, he is one of my heroes. His entire set of books is a must have.
If you’re serious about racing, you also owe it to yourself to familiarize yourself with the SCCA General Competition Rules (GCRs). Get the latest version from the SCCA’s website.
I just finished installing a Video VBOX Lite system in my car and am happy be driving my car again! It’s been 3 weeks since I started the project with 3-4 days of actual time spent. The biggest time sink was routing a microphone to the rear bumper which isn’t necessary but should make for a great sound track. I also lost a week to a wrong part being sent. If not for these two factors, install would have easily taken under a day.
Below is a video showing the output of my initial drive with the system recording just after completing the install, so minimal configuration. It’s not intended to be exciting (it’s not), but potentially informative for anybody considering a VBOX or evaluating similar systems.
VBOX is an in-car video and data acquisition system targeted at motorsports enthusiasts and racers who want to improve their driving by analyzing their driving after each session or event. I researched several different systems and opted for Racelogic’s Video VBOX system because it had most of the features I was looking for, was priced competitively, pre-sales support was responsive (which is a gauge for what I can expect post-sale), worldwide distributor network including two distributors in North America, good support site with monitored forums and regular updates, and an impressive product line.
The feature that attracted me to Video VBOX are:
- Multiple video inputs.
- Fully customizable video output.
- External stereo microphone input.
- CAN bus integration for getting at ECU data.
- High-resolution GPS and track mapping feature.
- Data stored to inexpensive, standardized SD card.
- Start/stop recording triggered by speed.
The one feature I wish VBOX had is HD video. There are other systems available with HD I opted for VBOX anyway because HD was a like-to-have for me, not must have. I purchased the VBOX lite, which is Racelogic’s least expensive system, as shown here:
I gave careful consideration to the installation prior to starting and opted as follows:
- VBOX stored inside glove box.
- 1-externally mounted microphone at rear of car (mono).
- 1-internally mounted microphone inside passenger cabin.
- 1 video extension cable routed back to roll bar.
- 1 CAN bus clip-on interface routed to driver-side foot well area.
- All other accessories, incl. power & GPS routed from glove box.
Layout schematic for all of the above is illustrated below.
VBOX Mounting Location
I considered two (2) locations for mounting the VBOX unit: Somewhere in the front trunk area and in the glove box. The biggest advantage of the front trunk is retaining full use of the glove box storage area, which the VBOX and all of its cabling pretty much fully occupy. However, I opted for the glove box for several reasons:
- Status LEDs able to be viewed without needing to get out of car.
- Easy access to record button if manual start / stop desired.
- No need to pop trunk to add / remove SD card.
- Easy to route cables in and out of glove box if needed.
- Close proximity to 12v power outlet (under dash).
- No need to route through wires through front bulkhead.
- Simply remove and store for safekeeping during offseason.
My overall goal was to minimize or eliminate need to make any modifications to the car in order to accommodate the system. By using the 12v power outlet I didn’t need to splice into any wires or tie into the fuse box. Racelogic also makes a clip-on interface that reads signals off of the CAN wires without needing to splice into them so I went this route as well. (More on the CAN interface below.)
The VBOX has a stereo microphone input and includes a splitter and two single channel condenser microphones so that left and right channels can be picked up at different points. I ran wires for mounting as follows:
- Inside cabin facing driver to pick up conversation and sounds hear by driver such as tires working. Also hoping that by pointing at driver from dash, wind buffeting will be kept to a minimum.
- External to car and hidden behind rear license plate facing downward. Not coincidentally, this also happens to be right over the exhaust tips.
I expect (hope) that this should make for some great audio tracks. Will probably require lowering exhaust channel level relative to cabin channel during editing in order to get a good balance.
My system accepts 2 camera inputs (more expensive models accept up to 4). Both are mounted from inside the vehicle:
- A high-resolution camera is attached to the windshield using a suction mount and faces forward across the hood of the car. This will provide an unobstructed view of the track and is the main video displayed.
- A low resolution camera is attached to the roll bar aiming at the driver from behind. This will be shown as an video inlay (picture-in-picture) and will be useful for accessing factors such as driver smoothness.
CAN bus signals are captured using Racelogic’s clip-on interface. This is nice for at least three (3) reasons:
- No need to alter the cars wiring harness.
- I was fairly confident I had the wires but not 100%. With the clip-on interface, no need to worry about hacking-up the electrical in search of the correct pair. Fortunately I got it right the first time thanks in-part to some thoughtful Internet posts.
- Non-physical interface for measuring signals means no chance of measurement affecting the signal and possibly causing CAN bus errors, which could in-turn affect vehicle operation.
The most obvious place to hook into the CAN signal was near the ECU since the pin-out schematic clearly identifies high and low CAN signals. However, it can also be picked-up of these same wires as they route up through the drivers foot well area near the fuse box. I opted for the latter because in the event of issues down the road, less stuff to need to tear into to diagnose and repair. (I apply this philosophy to all wire placement and routing considerations.)
The CAN bus interface is shown in the figure below and will be discussed in more detail with installation.
The bulk of the work involved with the install involved routing a microphone to the rear of the car. It’s a lot of work for just one (1) cable, but worth the effort in my opinion because it’ll return glorious audio tracks as opposed to the all too common wind-buffeting filled tracks heard on the Internet.
This is not a step-by-step guide so I’m only showing the basic flow. If you want to follow similar approach for your specific car, you can get detailed disassembly instructions on the Internet. Installing on a 2011 Porsche 911 GT3RS (997.2) and there was ample amounts of information on forums like Rennlist and Renntech that detailed anything I needed to know. For any Porsche 997 owners reading this, I’ll provide any 997 specific details that are not already amply posted about such as center console removal DIY.
CAN bus interface
A CAN interface is optional. Without it you’ll get the basics like video, audio, vehicle speed, g-forces, track mapping, lap timing. With it you can get a whole lot more data. What you get depends on your car. For my car (997.2 Porsche), I can get at:
- Lights on / off
- Reverse engagement
- Engine RPM
- Throttle position
- Parking brake engagement
- Road speed
- Brake position
- Steering direction
- Steering angle
- Wheel speed (RR)
- Wheel speed (RL)
- Wheel speed (FR)
- Wheel speed (FL)
- Clutch engagement
- Water temperature 1
- Water temperature 2
- Oil pressure
- Oil temperature
- Boost (my car is NA so does not apply)
- Gear selection
The VBOX lite only allows up to 4 CAN channels at a time, with the option to purchase up to 4 more for a total of 8 (purchased individually). I’m going to start with throttle position, steering angle, brake position, and gear selection. I’ll probably also purchase 1 extra for oil pressure.
With the VBOX unit you can get an unterminated CAN cable and wire directly into your system. But they also sell a clip-on interface that eliminates the need for splicing. It also guards against the VBOX system incidentally introducing any CAN signals onto your system’s CAN bus. I opted for the clip-on interface.
CAN bus clip-on interface and installation
If you’re using the CAN bus clip-on interface or if you have a Porsche 997 you may find this section useful if interfacing with your vehicle’s CAN bus.
The clip-on interface came with no instructions and it was immediately ambiguous to me regarding how to position the wires. The correct way in my non-humble opinion is to position the wires so that the surface area labeled CAN_H comes into contact with the CAN high wire when the shell halves are snapped together. However, some companies in an effort to make things easier for people outsmart themselves and just end-up making things more confusing. So I wondered did they mean for the upper half to read like a map for positioning the wires into the bottom as viewed during installation? Certainly, I’m thinking too hard about this but I did some checking after finding no documentation online and came across the promotion video for the interface showing the latter (reads like a map). Turns out the promotion video gets it wrong. (For BMW, which is the car used, CAN high is red-blue, and CAN low is red).
I contacted Racelogic support for clarification and they responded as follows (option1 is having the CAN high wire in contact with the surface area labeled CAN_H):
As for the ambiguity issue you are correct in thinking option 1 is correct. As we have had this question before I have contacted the developers of this and they are aware of this issue and are working on a new version that can be used either way round. Although we will have to make do with sticking to option 1 for now.
Also my opinion, I think they could save themselves some engineering investment and simply include a small piece of paper with the clip-on interface showing proper usage since it’s otherwise self-explanatory.
Also complicating my install was that VBOX sent me a clip-in interface for one of their higher-end (not VBOX Lite) which accepts a different style connector. Shown below is the other end of the cable for the interface I received, where as it should look like a PS2 connector from the outside. This added 1 week to my install while I waited on the part because it needed to be shipped from the UK. (Would have been longer if I didn’t foot the bill for overnight express which VBOXUSA was unwilling to do, so make sure you emphasize having them fulfill the order correctly for your system if ordering a VBOX CAN interface.)
Setup and Configuration
I’ve only just started to play with configuring my VBOX system. Except for reading the CAN data, everything was plug-and-play simple. Getting to where I could read the CAN data for my car took a little help from VBOX. Not getting anything at first begged the question if installation error or software configuration issue. I was very confident I had correct CAN wires and support clarified proper usage of the clip-on interface so either an issue with the clip-on interface itself or software configuration was my thought.
The issue turned out to be software configuration. VBOXUSA sent me a scene file for my car which had VBOX reading the CAN data; something I was unable to do using the CAN database file for the 997.2 Porsche. Different cars differ in how they use CAN to send data so you need model specific information which VBOX provides via their online vehicle CAN database. The database returns a file that gets read into the scene file loaded onto the VBOX telling it how to interpret the CAN signals.
The only other thing I needed to do to get the system ready for my initial (and successful) road test was aim the cameras. I purchased a small display that plugs into the AUX port on the VBOX and shows video in read-time. This makes setting up the cameras super easy. Just hold display in hand while adjusting each camera to desired position. The following figure is a photograph of the display screen:
Video showing trial run of system. This is with only minimal configuration so only minimal data is displayed and the brake pressure gauge needs reconfiguration. Goal of this drive was to simply check out video quality, confirm GPS working, etc. Just the basics.